EMT Practice Test

1. Question Content...

---

Question1: Which CA UIM Alarm Server (NAS) feature can be enabled automatically on a secondary NAS during HA failover?

Question2: In response to the needs of a specific customer, you create a group in Unified Service Manager (USM) with 600 servers. The group is populated with some baseline Monitoring Configuration Service (MCS) profiles for the cdm and processes probes. However, the customer subsequently tells you that 10 of the
600 servers require slightly different thresholds. Which action do you recommend?

Question3: In CA UIM 8.5.1. which probes are covered by Monitoring Configuration Service (MCS) templates?
(Choose three.)

Question4: You check the contents of a package in the archive and notice that it only contains a single file with a .cfx extension. What can you conclude from this?

Question5: You completed the nimldr installation on several Linux distributions. Now you need to enable the nimbus service. Which Linux command should you run to enable the service?

Question6: If a new hub is installed on the same network as the primary hub and the new hub is not appearing in the CA UIM GUIs, which troubleshooting steps are needed? (Choose two.)

Question7: You create an account for ClientA with ownership limited to the corresponding origin, and you add Bruce Adams as a contact for the account.
You assign a ClientAOperator access control list (copied from the Operator ACL) to Bruce. When Bruce logs in to the UMP for the first time:

Question8: You are attempting to set up monitoring on servers running Red Hat SELinux 7.1. You are unable to turn off the iptables firewall.
After getting a Linux robot up and running, you notice that the controller, spooler, and hdb robot probes all have green ports in infrastructure Manager and the controller and remote hub show no errors. However, you cannot open the controller GUI or contact it through the hub-to-robot connection. Only the connection from the robot to the hub, port 48002, works using Telnet. To address this issue, what do you need to do?

Question9: For robots configured behind a firewall, which ports must be opened for robots in proxy mode? (Choose two.)

Question10: UMP administrator Heather Marley signs in to the UMP and navigates to the Site Settings page where she specifies a friendly URL and the domain name that will be used for public and private pages. What is Heather configuring?

Question11: You are a CA UIM administrator in a financial organization. Your manager wants you to manage and monitor the highly secure network zone. The security policies do not allow any traffic to and from the highly secure network zone over the non-standard firewall policies. The ports above 48000, which are used for CA UIM communications, are considered to be nonstandard ports. To deploy bulk robots using CA UIM, which tasks are required?
1. Deploy a hub in the secure network zone and set up a tunnel.
2. Deploy a hub in the secure network zone but do not apply any probes to it.
3. Deploy the discovery_agent probe on the hub in the secure network zone.
4. Deploy the automated_deployment_engine (ade) probe on the hub in the secure network zone.
5. Ensure that HTTPS port 443 is open between the hub in the secure network zone and the tunnel server.

Question12: In Unified Services Manager (USM), you are attempting to discover Linux/UNIX servers on a remote site using the Discovery Wizard. However, no servers are discovered. You know that several servers exist at the remote site, as does a firewall with TCP ports 48000 to 48030 open.
Earlier, you successfully deployed robots on Windows and Linux target servers. In addition, Quality of Service (QoS) data is visible. Why is the Discovery Wizard failing to locate the servers?

Question13: Which port must be opened for the automatic_deployment_engine (ade) probe to deploy a robot on a UNIX system?

Question14: You just installed the UMP, opened it for the first time, and now need to define Service Level Agreements (SLAs). What should you do? (Choose two.)

Question15: CA UIM fails to communicate with a device hosted on a network protected by a firewall. Which command is used to test the routing from the CA UIM server to the device and from the device to the CA UIM server?

Question16: In your CA UIM infrastructure, the primary and remote hubs are connected through a firewall. To deploy robots automatically from the remote hub for deployment inside the firewall, which steps do you need to perform? (Choose three.)

Question17: When you create a tunnel certificate, what do you populate the Common Name field with?

Question18: When you build an Auto-Operator (AO) profile, which action do you perform?

Question19: By creating sites in the UMP, you can:

Question20: CA UIM server components automate the discovery of hosts and devices throughout your network. For discovery, which protocols are supported?

Question21: You have created a drop-down menu with several dashboards. Another UMP user wants to use this menu with its dashboards. She asks you to send her the files. Which step should you perform?

Question22: Which methods are valid for populating the snmpcollector? (Choose three.)