EMT Practice Test

1. Question Content...

---

Question1: Which statement describes how integrators use HP OneView to manage firmware on managed enclosures and servers?

Question2: A customer needs a Smart Array controller that will provide basic RAID protection, increased performance, and HP Secure Encryption in HP ProLiant Gen9 servers. Which Smart Array controller should the integrator choose?

Question3: Which pre-boot environment allows an integrator to update firmware with a fwupdate command?

Question4: Which resource can a server integrator use to verify whether VMware vSphere ESXi 5.5 U2 is supported on an HP BL460c Gen9 server?

Question5: A customer has an HP ProLiant DL380 Gen9 server and needs to order a power supply (PSU) model to meet the following requirements:
It must be a redundant PSU solution

The PSU must be able to handle a total load of 650 Watt, even in the event of a utility failure to one of

the two utility power feeds
Which PSU solutions should the integrator recommend to meet the customer's requirements? (Select two.)

Question6: What is required to successfully move from HP SIM to HP OneView?

Question7: A customer has an HP ProLiant DL380 Gen9 server that has no hard drives or SD card. The customer needs to install a virtualization Operating System on this server.
Which method should the integrator recommend?

Question8: What should the integrator use to back up HP OneView?

Question9: Which is an appropriate use of the HP OneView Dashboard?

Question10: An integrator needs to change the HP Smart Array P244br controller power mode to optimal settings based on a configuration with minimal performance impact on the server.
How should the integrator modify the power mode to perform the task?

Question11: A server integrator needs to install the maximum amount of memory in a new BL460с Gen9 server. Which type of memory should the integrator install?

Question12: Which HP software-defined platform automates management of HP servers, storage, and other HP Converged Infrastructure using RESTful API?

Question13: What is a benefit of advanced memory protection on HP ProLiant BL460c Gen9 servers?

Question14: A customer has an HP ProLiant DL380 Gen9 server with a Smart Array P440ar controller. The customer needs to add another internal drive cage and create a RAID set using all internal drives. Which HP component should the integrator install in the HP ProLiant DL380 Gen9 server?

Question15: A customer needs eight SAS drives installed in a RAID 10 configuration in their new HP ProLiant DL380 Gen9 server, using the Dynamic Smart Array B140i Controller embedded into the system. The drives are installed properly in the bays. When the integrator attempts to configure the array, the drives do not appear in the configuration utility.
What is the likely cause of the problem?

Question16: A customer with ProLiant Gen9 based servers needs to add external storage to some of the servers Which component should the integrator recommend?

Question17: A customer is planning where to locate their servers in the data center and how to manage and monitor power consumption. They have purchased HP iPDU units for the cabinets where HP ProLiant Gen9 servers will be installed.
Which guideline must the integrator follow when installing the new iPDUs?

Question18: While creating a baseline for the Gen9 blades in a new c7000 BladeSystem Enclosure in an active/active configuration, the integrator determines that one blade has an NIC teaming setting of fail over.
What will be the outcome of this setting in an active/active high availability configuration?

Question19: A company is upgrading its data center to HP ProLiant Gen9 servers. An integrator is investigating whether this upgrade will allow them to decrease cooling costs by operating IT Equipment inlet air temperature close to 104° F (40° C).
Under which circumstance should the integrator plan to keep the IT Equipment inlet air temperature below
95° F (35° С)?

Question20: Power was lost to an HP ProLiant DL380 Gen9 Server. The system ROM is now corrupted and the server can no longer boot.
What should the integrator do first to correct this problem?

Question21: A customer has two HP с7000 BladeSystem Enclosures equipped with Virtual Connect FlexFabric
10Gb/24-Port interconnect modules and is managing this environment with HP OneView. Both enclosures are members of one enclosure group. The integrator needs to add a new enclosure to the Infrastructure and configure Virtual Connect modules identically to the current enclosures as follows:
Identical uplink ports to carry Ethernet and Fibre Channel traffic

Identical networks and VLAN IDs

Identical IGMP settings

The new enclosure will be equipped with Virtual Connect FlexFabric-20/40 F8 interconnected modules

Which approach should the integrator take?

Question22: How do HP Intelligent Power Distribution Units (iPDUs) help server integrators?

Question23: A customer has added a storage blade to their current с7000 BladeSystem Enclosure, however the external storage is not visible from the adjacent HP ProLiant BL460c Gen9 server blade.
What should the integrator do in order for the ProLiant BL460c Gen9 server blade to recognize the adjacent storage?

Question24: A customer needs to deploy a legacy operating system on an HP DL380 Gen9 Server. The integrator sets the BIOS to support Legacy BIOS Boot Mode. When the integrator attempts to install the operating system, the embedded controller and disk drives are not available for configuration.
What should the integrator do to resolve this issue?

Question25: How should the server integrator use to standardize settings for HP BladeSystem Enclosure interconnect modules?

Question26: A system integrator installed an operating system on an HP ProLiant Gen9 Server. Which operating system can be used with UEFI Boot Mode?

Question27: An integrator needs to deploy an HP OneView appliance to the ESXi Server managed by the vCenter Server. Which tool can the integrator use to access the vCenter Server?

Question28: What is a benefit of using 20Gb FlexFabric Converged network adapter (CNA) for the BladeSystems?

Question29: An integrator is installing an HP ProLiant DL380 Gen9 server with an H240ar controller installed. The integrator needs to install a total of 24 SFF Drives.
Which additional task must the integrator perform to meet the requirements?

Question30: A customer has an HP ProLiant DL380 Gen9 server with one processor that has a large RAID 5 SAS Array configured on a P440ar storage controller with a hot spare. During the rebuild process, a second SAS drive failed.
What should the integrator do to help prevent this problem from reoccurring?

Question31: An integrator needs to install Windows Server 2012 R2 on 6 HP ProLiant BL460c Gen9 servers The servers will be part of an SQL cluster and must be configured identically. The integrator needs to use Intelligent Provisioning to complete this task.
What does Intelligent Provisioning use to allow the integrator to create deployment settings profiles to make this process more efficient?

Question32: A customer needs to implement HP OneView to manage a data center based on Gen9 servers running Windows, OpenStack, and VMware.
Which other component can the integrator implement in this environment?

Question33: An integrator is preparing for an HP OneView installation. Which software component needs to be installed at the customer site before the integrator can perform the installation?

Question34: An integrator is installing an HP ProLiant BL460c Gen9 server into device bay 13 of an HP c7000 BladeSystem Enclosure. The integrator needs to access the UEFI System Utilities on the new server, but is unable to do so because the iLO4 Integrated Remote Console is not accessible.
Where can the integrator confirm the IP address of the iLO4 interface for this blade?

Question35: An integrator needs to install an operating system on an HP ProLiant Gen9-series server using the HP Dynamic Smart Array B140i Controller.
What should the integrator do?

Question36: A server integrator has selected Virtual Connect Flex-10/10D modules as interconnect modules for HP BladeSystem Enclosures. Blade servers will use Fibre Channel over Ethernet (FCoE) for their remote storage. The integrator is now discussing the upstream connectivity requirements with LAN and SAN administrators.
Which solution should the integrator choose to connect to the Virtual Connect modules?