EMT Practice Test

1. Question Content...

---

Question1: You are asked to add a new HA pair to an existing 2-node switchless AFF A220 cluster. You must first convert to a 2-node switched cluster using Broadcom BES-53248 cluster switches.
Which two conditions must be fulfilled before you start the migration? (Choose two.)

Question2: Your customer wants a newly installed AFF C190 cluster to send SNMP notifications to a trap host called OVERWATCH01.
In this scenario, which two statements are correct? (Choose two.)

Question3: You need to install a cluster with a FAS2720 HA pair and a FAS8300 HA pair.
Which NetApp tool will verify which cluster interconnect switches support this configuration?

Question4: You want to verify that connections are cables correctly and that shelf IDs are unique within an HA pair.
Which tool would be used to accomplish these tasks?

Question5: You are a NetApp Professional Services engineer, employed by NetApp. You have just completed an ONTAP cluster installation. You need to collect the relevant configuration information to enable the Service Event Report (SER) to be created.
Which tool would you use to accomplish this task?

Question6: Click the Exhibit button.

You are adding new DS224C shelves in a new stack to your cluster with FAS8060 controllers running ONTAP 9.7.
Referring to the exhibit, which two actions should be performed to the cluster before installing the new shelves? (Choose two.)

Question7: When you install a new ONTAP 9.7 4-node cluster, which network type is required?

Question8: After completing the installation of an AFF A800 ONTAP AI cluster, you are asked which contacts are available for additional help in obtaining immediate assistance in solving P1 issues.
In this scenario, what do you tell the customer?

Question9: Click the Exhibit button.

As shown in the exhibit, you have an 8-node ONTAP 9.7 cluster. You are asked to set up a SnapMirror volume relationship between node-1 and node-8 in the same cluster.
In this scenario, which two network components are used by the SnapMirror volume? (Choose two.)

Question10: You use the system health subsystem show command to troubleshoot your newly installed ONTAP cluster.
In this scenario, which two health outputs would this command show you? (Choose two.)

Question11: You have an AFF All SAN Array (ASA) cluster that is running ONTAP 9.7. The cluster is configured for Active Directory domain controller access using a domain tunnel.
In this scenario, which two licenses are enabled on the cluster? (Choose two.)

Question12: You are planning to install a new ONTAP 9.7 All SAN Array (ASA) into your existing data center.
In this scenario, which cluster configuration is allowed with ASA controllers?

Question13: Click the Exhibit button.

A customer has two Cisco 40GbE data switches. They want to connect the switches to an AFF A400 HA pair. The switches and the AFF A400 are approximately seven meters apart.
Referring to the exhibit, which two supported actions would allow you to accomplish this task? (Choose two.)

Question14: In ONTAP 9.7 software, how many different replicated databases (RDBs) exist per node?

Question15: Click the Exhibit button.

You are installing a new FAS cluster. The management network must be on tagged VLAN 11 for remote administration by a service provider.
Referring to the exhibit, which two ports will allow service provider access to both cluster and node management LIFs? (Choose two.)

Question16: You are installing a new ONTAP 9.7 cluster by following the installation and setup poster. You are ready to complete the initial cluster setup. You have connected your laptop to the management switch. However, when browsing the network, you are unable to discover the ONTAP controllers.
Which statement explains this behavior?

Question17: You are installing a new AFF A400 cluster and need to access the cluster management LIF from a remote subnet with the fully qualified domain name (FQDN) a400.lab.netapp.com.
In this scenario, which two network components must be configured to log in to ONTAP System Manager from the remote subnet? (Choose two.)

Question18: You are installing a new FAS2750 cluster with 24 HDDs for a customer to run a NAS workload. The customer requests that the HA pair have only a single aggregate that is located on Node 1. Maximum capacity is required.
Which action must be performed to ensure that the customer's requests are satisfied?

Question19: You are setting up a new AFF A400 that will serve iSCSI LUNs. You will have four iSCSI SVMs that each need to connect to an Internet Storage Name Service (iSNS) for discovery and management purposes.
In this scenario, which network interface is needed for each SVM to register with the name service?

Question20: In an ONTAP 9.7 cluster, which LIF role is used for sending AutoSupport, establishing Network Time Protocol (NTP), and loading software updates?

Question21: One of the nodes in your ONTAP 9.7 cluster has failed and is not coming back online.
Which two methods would you use to connect to the node failing to come back online? (Choose two.)