EMT Practice Test

1. Question Content...

---

Question1: Click the Exhibit button.

You receive the same 75.100.0.0/16 route from all four ISPs to which you are connected.
Referring to the exhibit, which ISP's route will be selected as active?

Question2: Which two statements are correct about a functional ESI LAG interface? (Choose two )

Question3: Click the Exhibit button.

Referring to the exhibit, you must advertise the 100.0.0.0/16 routes from AS1 to AS2, but R2 is not advertising any BGP routes to R5.
Why is this happening in this scenario?

Question4: Click the Exhibit button.

You are configuring an EVPN overlay to allow VLANs to be stretched between two campus sites, but EVPN routes are not being exchanged.
Referring to the exhibit, which configuration statement would solve this problem?

Question5: Click the Exhibit button.

Which well-known community needs to be used to restrict 10.0.0.0/8 from being advertised to AS 2?

Question6: You have an IPv4 multicast network configured as PIM-SM.
What must be done before replacing your static RP with auto-RP?

Question7: You have configured CoS on a Junos device. A packet is classified as best effort by a behavior aggregate (BA) classifier, and as expedited forwarding by a multifield (MF) classifier.
Which statement is true in this scenario?

Question8: Click the Exhibit button.

The policy shown in the exhibit is applied as an export policy to your BGP neighborship.
Which action will be taken for route 12.233.45.5?

Question9: You are implementing 802.1x authentication in your Layer 2 network. Each user will have a computer and a phone and you must ensure that both device are authenticated individually.
In this scenario, which supplicant mode should be used?

Question10: Click the Exhibit button.

You are configuring BGP policies for a site with a dual-homed connection as shown in the exhibit. You must ensure that inbound traffic from Internet hosts flow through the ISP A connection.
Which statement is correct in this scenario?

Question11: Which BGP message type contains NLRI information?

Question12: What are two supported PoE management modes? (Choose two.)

Question13: You have PIM SM multicast configure and running in a network environment comprised of EX4300 devices. Your customer report increased delay when switching channels using IPTV. To help decrease the delay, you implement PIM join balancing. You add the set protocol pim join-load-balance command to the configuration. After committing, you notice that the flows are still using one path.
In this scenario, which statement is correct?

Question14: You are deploying IP phones to a customer site. The IP phones will be installed to share a common access port with the user's desktop computer. You are required to provide a mechanism to place user data traffic and voice traffic in different VLANs for class-service application How would you implement this solution?

Question15: Click the Exhibit button.

Referring to the exhibit, how is R1 learning the route from R2?
R2 has an export policy with external type 2 configured.

Question16: Exhibit:

You are authenticating user devices connected to your ex Series switch. You have 802.1X and MAC RADIUS configured for all ports A user is complaining about the time it takes to connect their non-802.1X device on ge-0/0/15 using MAC RADIUS authentication Referring to the exhibit, what should be done to accelerate the authentication process?

Question17: Which two statements about OSPF routing policies are correct? (Choose two.)

Question18: Exhibit.

Which two statements are true about the 802. 1X output shown in the exhibit? (Choose two.)

Question19: Click the Exhibit button.

Referring to the exhibit, the source is currently sending multicast traffic using group 224.1.1.1, which is being received by R1. R2 is not receiving PIM register messages.
What would be the cause of this problem?

Question20: Your network has Junos Fusion configured with MX960 routers as aggregation devices (AD) and QFX5100 switches as satellite devices (SO) Which two statements are coned in this scenario? (Choose two )

Question21: Which two statements about BGP communities are true? (Choose two.)

Question22: Click the Exhibit button.

Referring to the exhibit, which statement is correct?

Question23: You are 802.1X supplicant, but traffic must be accepted once the user has authenticated their computer on the port In this scenario, which supplicant mode should be used?

Question24: Exhibit.

Referring to the exhibit, which TTL value will be sent to the LLDP neighbors?

Question25: You must ensure that all management traffic sourced from your Junos devices is set with a specific DSCP code-point value.
Which action will accomplish this task?

Question26: Click the Exhibit button.

You have configured and applied the policer shown in the exhibit to your Junos device.
Which statement is true in this scenario?

Question27: Click the Exhibit button.

You are investigating reports of increased latency and discover that some routes cause customer traffic to traverse a route reflector instead of the optimal path.
Referring to the exhibit, which configuration statement would solve the problem?

Question28: What is the correct authentication processing order on EX Series switches when multiple Layer 2 authentication methods are enabled?

Question29: Click the Exhibit button.

You are adding VNI 101 to your EVPN-VXLAN network, but traffic is not being sent or received.
Referring to the exhibit, which configuration statement will solve the problem?

Question30: Packets enter a Juniper device and are classified as best effort. During the processing of the packet, the classification of the packets is changed to expedited forwarding by a multi-field classifier. The device is using the default CoS policies Which statement is true in this scenario?

Question31: You receive the same 100.200.0/16 route from all four ISPs to which you are connected.
Referring to the exhibit, which ISP's route will be selected as active?

Question32: When configuring class of services, what would be you use to allocate bandwidth to a forwarding class?