EMT Practice Test

1. Question Content...

---

Question1: Click the Exhibit button. Referring to the exhibit, how is R5 able to learn the networks that exist within the NSSA?

Question2: You are enabling MSTP in your Layer 2 network to prevent loops. In this scenario, which three parameters must match on all switches in the network? (Choose three. )

Question3: You ate deploying P|M source-specific multicast (SSM) for a new multicast messaging service You have configured the multicast source to use 236.44.123.100 as the multicast address. You are not able to join the PIM SSM multicast teed Which two solutions would resolve this problem? (Choose two )

Question4: You are troubleshooting an OSPF adjacency issue between R1 and R2.

What is the reason for the ExStart state shown in the exhibit?

Question5: You are asked to merge a RIP network with your OSPF network. As a first step, you establish connectivity between the RIP network and the OSPF network. The RIP network connects to an NSSA area. Which two statements are true in this scenario? (Choose two.)

Question6: You are configuring, the PVLAN feature on your switches. The PVLAN will span the two EX Series switches shown in the exhibit.
Which three configuration parameters must be enabled on the ports connecting the two switches?
(Choose three. )

Question7: You notice a mass withdrawal of routes for some of the network hosts. You determine that the link on the ESI interface is down.
Which route type is used in this scenario?

Question8: Referring to the exhibit, which statement is correct?

Question9: Which two statements are correct about a functional ESI LAG interface? (Choose two )

Question10: You are implementing CoS for a custom application that is labeling its packets with DSCP code- point 101111. You have applied the configuration shown in the exhibit, but not that while some custom application traffic ingressin on ge-0/0/1 transits the SRX Series device successfully, packets ingressing all other ge-* interfaces are being dropped.
Which action should you take to solve this problem?

Question11: Router R1, in peer AS 65001, advertises routes to R2 using EBGP. R2 advertises the routes learned from R1 to R3 using IBGP.

Referring to the exhibit, to which routers will R3 advertise the BGP routes received from R2?

Question12: which protocol is a multicast routing protocol?

Question13: When configuring 802.1X authentication, what are three server fail fallback settings? (Choose three.)

Question14: Click the Exhibit.


You have just configured on an OSPF adjacency between two routers. After you commit the configuration, you notice that your adjacency is not up.
Referring to the exhibit, what would cause the problem?

Question15: Referring to the log shown in the exhibit, what is the problem with the OSPF adjacency establishment?

Question16: You recently implemented the configurations shown in the exhibit. After committing these changes, the community devices connected to AS-1 are not able to communication with the appropriate community devices connected to AS-2.
What must be to allow these community devices to communicate?

Question17: Click the Exhibit.

You have a workstation and VoIP phone connected to port ge-0/0/1 on an access switch.
Referring to the configuration shown in the exhibit, which statement is true?

Question18: Click the Exhibit button.

There is a functioning OSPFv3 neighborship between Router-1 and Router-2 over the ge-0/0/1 link. However, the 172.100.100.0/24 and 172.101.101.100/24 routes are not being shared through OSPFv3.
Referring to the configuration shown in the exhibit, which two actions must you take to solve the problem? (Choose two.)

Question19: Click the Exhibit button.

During an outage, you review the status of the Q-in-Q implementation on VLAN 300.
Referring to the exhibit, what would be the cause of the outage?

Question20: What are two OSPF LSA types? (Choose two.)

Question21: The policy shown in the exhibit is applied as an export policy to your BGP neighborship.
Which action will be taken for route 12.233.45.5?

Question22: You have multiple BGP routes to the same prefix with equal local-preference values and AS-path lengths.
In this scenario, which route will be preferred in the route selection process?

Question23: You are deploying IP phones to a customer site. The IP phones will be installed to share a common access port with the user's desktop computer. You are required to provide a mechanism to place user data traffic and voice traffic in different VLANs for class-service application How would you implement this solution?

Question24: Your Net is learning the 210.210.40.0/24 route from Provider A and Provider B YourNet would like to forward traffic destined to the 210.210.40.0/24 networking using Provider B.
Referring to the exhibit, how would you accomplish this task?

Question25: Refer to Exhibit:

You have a workstation and a VoIP phone connected to port ge-0/0/1 on an access switch.
Referring to the exhibit, which two statements are true? (Choose two.)

Question26: Referring to the exhibit, a RMSM network is set up to enable communication between multicast devices.
Which statement is true in this scenario?

Question27: You are 802.1X supplicant, but traffic must be accepted once the user has authenticated their computer on the port In this scenario, which supplicant mode should be used?

Question28: Which two port modes are associated with STP? (Choose two.)

Question29: Which statement is correct about CoS policers on Junos devices?

Question30: You have an IPv4 multicast network configured as PIM-SM. What must be done before replacing your static RP with auto-RP?

Question31: What is the correct authentication processing order on EX Series switches when multiple Layer 2 authentication methods are enabled?

Question32: You are configuring MVRP for automatic VLAN registration. Which two statements are true?
(Choose two.)

Question33: Your IPv4 multicast network uses different MX Series routers for the source DR and the PIM sparse-mode RP.
What is required before PIM register messages are exchanged between the DR and RP routers?

Question34: Referring to the exhibit, which TTL value will be sent to the LLDP neighbors?

Question35: Which statement is correct about MSTP?

Question36: Click the Exhibit.

The Receiver is attempting to join two different groups, one from each source. You want to endure that load balancing is taking place.
Referring to the exhibit, which statement is true?

Question37: Click the Exhibit button.

Which well-known community needs to be used to restrict 10.0.0.0/8 from being advertised to AS
2?

Question38: Which two statements about OSPF routing policies are correct? (Choose two.)

Question39: You have configured 802.1X single supplicant mode on the access switch. The VoIP phone does not support 802.1X authentication.

Referring to the exhibit, which statement is true?

Question40: Referring to the exhibit, which statement is true?

Question41: Click the Exhibit button.

You receive the same 75.100.0.0/16 route from all four ISPs to which you are connected.
Referring to the exhibit, which ISP's route will be selected as active?